RG6 and RG6 Quad connector installation
I work for a factory that makes wire harnesses for RV's. I'm in charge of all coax end installation. I usually install about 1000 Thomas Betts SNSRG6QS connectors a week and sometimes 600 per day. Right now we are using all Belden RG6 which I know they should be using the RG6 connectors on and not the QS but but they don't care. But my issue is that the customer is looking to switch to Belden RG6 Quad Sheild cable. We got a spool in the other day and I have been testing out ways to install the connectors quickly since I would have to do so many ends. The instructions that come in the box of connectors says you should peel back the first braiding then slit the first foil and then peel back the rest of the braiding then install the connector. As you know that takes a while to do all of that for one connector, so I got online and tried looking around and it said to set my stripper to cut threw the first set of braiding and foil and peel back the inner braid and put the connector on. Which way should I be doing it, because I know if i strip threw it, it would make it go a lot faster but is the electrical contact between the sheilding going to be up to standard? I purchased a coax flaring tool to try on it but just using that isn't going to work because you still have that outter foil on there and the connector will not go flush. Normally I can install a single connector on RG6 cable from start to finish in about 10 seconds, with the quad sheild I was only getting about 20-30 seconds per connector, and when you times that by the amount of connectors installed it adds up. Jay, that's really a question for the Pro's, so I'd suggest checking out the forums at someplace like www.satelliteguys.us, where you are likely to get some decent advice. By the way, TB makes a connector that is designed for both RG-6 and RG-6 quad. Part number is SNS1P6U. Same price as the Quad shield connectors at every supplier I've encountered. Might be worth mentioning to the purchasing department. Not as snug a fit on the jacket of dual or tri-shield as the connectors designed for those cables, but will grip better than a QS on a non-QS cable. Originally Posted by jaylaudeman I work for a factory that makes wire harnesses for RV's. I'm in charge of all coax end installation. I usually install about 1000 Thomas Betts SNSRG6QS connectors a week and sometimes 600 per day. Right now we are using all Belden RG6 which I know they should be using the RG6 connectors on and not the QS but but they don't care. But my issue is that the customer is looking to switch to Belden RG6 Quad Sheild cable. We got a spool in the other day and I have been testing out ways to install the connectors quickly since I would have to do so many ends. The instructions that come in the box of connectors says you should peel back the first braiding then slit the first foil and then peel back the rest of the braiding then install the connector. As you know that takes a while to do all of that for one connector, so I got online and tried looking around and it said to set my stripper to cut threw the first set of braiding and foil and peel back the inner braid and put the connector on. Which way should I be doing it, because I know if i strip threw it, it would make it go a lot faster but is the electrical contact between the sheilding going to be up to standard? I purchased a coax flaring tool to try on it but just using that isn't going to work because you still have that outter foil on there and the connector will not go flush. Normally I can install a single connector on RG6 cable from start to finish in about 10 seconds, with the quad sheild I was only getting about 20-30 seconds per connector, and when you times that by the amount of connectors installed it adds up. do you own a cable stripper that is adjustable?
Related Posts:
Two romex cables through one connector
Two Romex cables through one connector?Is it legal to secure two Romex cables through one connector? Can Romex be stapled on top of another? Thanks Bill If the connector is listed for multiple cab...
Whats a gutter installation cost
What's a gutter installation cost?The house I'm buying is a rectangle one story and 1300 sqft. It has an attached garage. The roof was replaced and the outside was painted recently but it appears...
The horror of triangle tube prestige installation
The horror of (Triangle Tube Prestige Installation)trying to find an installer that will install a Triangle Tube Prestige. I have a 1914 house that has been gutted, re-insulated and put back toget...
Rg6 vs rg6 quad
rg6 vs. rg6 quadIs it worth the trouble replacing rg6 cable with rg6 quad? Would I see any picture improvements in HD? Probably not - it tends to be less susceptible to interference but carries th...
Shallow well pump installation
Shallow Well Pump (Installation)I've been browsing through alot of these threads,and still have quite e few questions about installing a pump for my camp.The pump is a 1/2 horse Sears shallow well...
